TYPE | GPB1B5 _ _ _ _ | GPB1D5 _ _ _ _ | GPB1B6 _ _ _ _ | GPB1C6 _ _ _ _ |
PRESSURE RANGE | 0 to -101,3 kPa | 0 to 0,6 Mpa | 0 to -101,3 kPa | 0 to 1,0 MPa |
WITHSTAND PRESSURE | 0,6 MPa | 1,5 MPa | 0,2 MPa | 1,5 MPa |
ACCURANCY | ±3% F.S. of detected pressure @ 25°C | ±2% F.S. of detected pressure @ 25°C | ||
RATED VOLTAGE | 12 to 24 V DC (±10% ripple voltage) | |||
OUTPUT TYPE | PNP | Analog | ||
Open collector 2 outputs, max current load: 80 mA | 1 to 5V ± 1% F.S. | |||
CURRENT CONSUPTION MAX. | 10 mA |
OUTPUT SHORT CIRCUIT PROTECTION | yes | no |
RESPONSE TIME | 1,5 ms max | |
REPEATIBILITY | ± 1% F.S, | - |
HYSTERESIS | 3% F.S. max. | - |
FUNCTION INDICATOR | Red LED turns ON | - |
ENVIROMENTAL CONDITIONS | min. 0°C ; max. 50°C (No condensation or freezing) | |
TEMPERATURE OPERATION RANGE | min. -20°C ; max. 60°C (No condensation) | |
TEMPERATURE STORAGE RANGE | Operation/Storage: 35 to 85 % RH | |
AMBIENT HUMIDITY RANGE | Total amplidude 1,5mm, 10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X,Y and Z | |
VIBRATION | 980m/s2(100G), 3 times each direction of X,Y and Z | |
SHOCK | IP40 when correctly assembled | |
PROTECTION CLASS (EN 60529) | ||
CABLE TYPE | oil - resistance (0,18mm2) | |
WEIGHT | approx. 50g (with 2m lead wire) |
OPTION A / B / C | OPTION D | OPTION E | OPTION F |
![]() |
![]() |
![]() |
![]() |
![]() |
|||
HOW TO SET PRESSURE
Use the pressure setting trimmer to set "ON" pressure. Totate clockwise to increase pressure set point.
Rotate counter-clockwise to decrease pressure setpoiny. Use appropriate size screwdriver for the setting trimmers. Gently turn the screwdriver to make adjustments.
To prevent demage to the pressure setting trimmer, DO NOT force the trimmer when it comes to a stop
|
|||
INSTALLATION PRECAUTION
When mounting, always use the wrench on the metallic area near the pressure port.Never apply a wrench to the plastic body, it will demage the sensor. Over lightening may cause demages the port thread, mounting bracket and pressure sensor.Under ightening may result loosen or leakage. Apply pressure and power after installation and make necessart adjustments and inspect any possible signs of leakage to ensure proper installation. |
TYPE | GPB2A5 _ _ _ _ | GPB2B5 _ _ _ _ | GPB2C5 _ _ _ _ |
PRESSURE RANGE | -100,0 to +100,0 kPa | 0,0 to -101,3 kPa | 0,000 to 1,000 MPa |
WITHSTAND PRESSURE | 300 kPa | 300 kPa | 1,5 MPa |
ACCURANCY | ±1% F.S. of detected pressure @ 25°C ± 3°C | ||
RATED VOLTAGE | 12 to 24 V DC (±10% ripple voltage) | ||
OUTPUT TYPE | Open collector 1 outputs, max current load: 80 mA | ||
WITHSTAND VOLTAGE | 1000V AC in 1 min. (at 500V DC, between case and lead cable) | ||
CURRENT CONSUPTION MAX. | 21 mA max. | ||
INSULATION RESISTANCE | 50Mohm min. (at 500V DC, between case and lead cable) |
OUTPUT SHORT CIRCUIT PROTECTION | yes |
RESPONSE TIME | 5 ms max |
REPEATIBILITY | ± 1% F.S. |
HYSTERESIS | 1 to 10 % of setting pressure (adjustable) |
FUNCTION INDICATOR | Red LED turns ON |
ENVIROMENTAL CONDITIONS | min. 0°C ; max. 50°C (No condensation or freezing) |
TEMPERATURE OPERATION RANGE | min. 0°C ; max. 50°C (No condensation or freezing) |
TEMPERATURE STORAGE RANGE | min. -20°C ; max. 60°C (No condensation) |
AMBIENT HUMIDITY RANGE | Operation/Storage: 35 to 85 % RH |
VIBRATION | Total amplidude 1,5mm, 10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X,Y and Z |
SHOCK | 980m/s2 (100G), 3 times each direction of X,Y and Z |
PROTECTION CLASS (EN 60529) | IP40 when correctly assembled |
CABLE TYPE | oil - resistance (0,18mm2) |
WEIGHT | approx. 60g |
DIMENSION / CONNECTION
![]() |
|
HOW TO SET PRESSURE
Remove dust cover to make any adjustments. Replace dust cover when finished to preventforeign object from entering. Pressure setting trimmer (SET) is for setting the output (ON) pressure. Rotate SET trimmer counter-clockwise to increase (Pressure or Vacuum) the ON point. Rotate clockwise will decrease the setting pressure.Hysteresis setting trimmer (HYS) is for changing the hysteresis. Rotate trimmer counter-clockwise to increase the range 1 - 1 Use appropriate size screwdriver for the setting trimmers. Gently turn the screwdriver to make adjustments. Do not force the trimmer when it comes to a stop to prevent demage to the setting trimmer |
|
INSTALLATION PRECAUTION
When mounting, always use the wrech on the metallic area near the pressure port. Never apply a wrench to the plastic body, it will demage the sensor.Over tightening may cause demages to the port thread, mounting bracket and pressure sensor. Under tightening may result loosen or leakage. Apply pressure and power after installation and make necessary adjustments and inspect any possible signs of leakage to ensure proper installation. |
TYPE | GPB3A _ _ _ _ | GPB3B _ _ _ _ | GPB3C _ _ _ _ |
PRESSURE RANGE | -100,0 to +100,0 kPa | 0,0 to -101,3 kPa | 0,000 to 1,000 MPa |
WITHSTAND PRESSURE | 300 kPa | 300 kPa | 1,5 MPa |
SET PRESSURE RESOLUTION | |||
kPa | 0,1 | 0,1 | - |
MPa | - | - | 0,001 |
kgf/cm2 | 0,001 | 0,001 | 0,01 |
bar | 0,001 | 0,001 | 0,01 |
psi | 0,01 | 0,01 | 0,1 |
inHg | 0,1 | 0,1 | - |
mmHg | 1 | 1 | - |
mmH2O | 0,1 | 0,1 | - |
ACCURANCY | ±2% F.S. ±1 digit of detected pressure @ 25°C ± 3°C | ||
RATED VOLTAGE | 12 to 24 V DC (±10% ripple voltage) | ||
OUTPUT TYPE | |||
PNP | Open collector 2 outputs, max current load: 80 mA | ||
ANALOG | 1 to 5V ± 2,5% F.S. | ||
INSULATION RESISTANCE | 1 to 5V ± 5% F.S. | 60 mA |
OUTPUT SHORT CIRCUIT PROTECTION | yes |
RESPONSE TIME | 2.5 ms max (anti-chattering selection:24ms, 192 and 768) |
REPEATIBILITY | ± 0,2% F.S. ± 1 digit |
HYSTERESIS MODE | Adjustable |
WINDOW COMPARATOR MODE | Fixed ( 3 digit) |
FUNCTION INDICATOR | OUT1 = Green ; OUT2 = Red |
ENVIROMENTAL CONDITIONS | |
TEMPERATURE OPERATION RANGE | min. 0°C ; max. 50°C (No condensation or freezing) |
TEMPERATURE STORAGE RANGE | min. -20°C ; max. 60°C (No condensation) |
AMBIENT HUMIDITY RANGE | Operation/Storage: 35 to 85 % RH |
VIBRATION | Total amplidude 1,5mm, 10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X,Y and Z |
SHOCK | 980m/s2(100G), 3 times each direction of X,Y and Z |
PROTECTION CLASS (EN 60529) | IP40 |
CABLE TYPE | oil - resistance (0,15mm2) |
WEIGHT | approx. 67g (with 2m lead wire), Approx. 35g (with male connector) |
DIMENSION
![]() |
|
HOW TO SET PRESSURE
![]() |
|
Button UP | Use this button to change setting mode and pre-set final desired value |
Button SET | Change setting mode and pre-set final desired valuee |
Button DOWN | Use this button to change setting mode and pre-set final desired value |
Switch OUT1 | Green LED |
Switch OUT2 | Red LED |
Display | Pressure value display |
TYPE | GPB4A _ _ _ _ | GPB4B_ _ _ _ | GPB4C _ _ _ _ |
PRESSURE RANGE | -100,0 to +100,0 kPa | 0,0 to -101,3 kPa | 0,000 to 1,000 MPa |
WITHSTAND PRESSURE | 300 kPa | 300 kPa | 1,5 MPa |
SET PRESSURE RESOLUTION | |||
kPa | 0,1 | 0,1 | - |
MPa | - | - | 0,001 |
kgf/cm2 | 0,001 | 0,001 | 0,01 |
bar | 0,001 | 0,001 | 0,01 |
psi | 0,01 | 0,01 | 0,1 |
inHg | 0,1 | 0,1 | - |
mmHg | 1 | 1 | - |
mmH2O | 0,1 | 0,1 | - |
ACCURANCY | ±2% F.S. ±1 digit of detected pressure @ 25°C ± 3°C | ||
FLUID | Air, Non-corrosive/Non-flammable gas | ||
RATED VOLTAGE | 12 to 24 V DC (±10% ripple voltage) | ||
OUTPUT TYPE | |||
PNP | Open collector 2 outputs, max current load: 80 mA | ||
ANALOG | 1 to 5V ± 2,5% F.S. | ||
CURRENT CONSUPTION MAX. | 1 to 5V ± 5% F.S. | 55 mA |
OUTPUT SHORT CIRCUIT PROTECTION | yes |
RESPONSE TIME | 2.5 ms max (anti-chattering selection:24ms, 192 and 768) |
REPEATIBILITY | ± 0,2% F.S. ± 1 digit |
HYSTERESIS MODE | Adjustable |
WINDOW COMPARATOR MODE | Fixed (3 digit) |
FUNCTION INDICATOR | OUT1 = Green ; OUT2 = Red |
ENVIROMENTAL CONDITIONS | |
TEMPERATURE OPERATION RANGE | min. 0°C ; max. 50°C (No condensation or freezing) |
TEMPERATURE STORAGE RANGE | min. -20°C ; max. 60°C (No condensation) |
AMBIENT HUMIDITY RANGE | Operation/Storage: 35 to 85 % RH |
VIBRATION | Total amplidude 1,5mm, 10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X,Y and Z |
SHOCK | 980m/s2(100G), 3 times each direction of X,Y and Z |
PROTECTION CLASS (EN 60529) | IP65 when correctly assembled |
CABLE TYPE | oil - resistance (0,15mm2) |
WEIGHT | approx. 105g (with 2m lead wire), Approx. 71g (with male connector) |
Order no. GPA4S | Order no. GPA4L | Order no. GPA4P |
Vertical mounting brackets | Base mounting brackets | Panel adapter |
![]() |
![]() |
![]() |
DIMENSION
![]() |
||
PANEL INSTRUCTION
![]() |
||
Button UP | Use this button to change setting mode and pre-set final desired value | |
Button SET | Change setting mode and pre-set final desired valuee | |
Button DOWN | Use this button to change setting mode and pre-set final desired value | |
Switch OUT1 | Green LED | |
Switch OUT2 | Red LED | |
Display | Pressure value display |
TYPE | GPB5A_ _ _ _ _ | GPB5B_ _ _ _ _ | GPB5C_ _ _ _ _ |
PRESSURE RANGE | -100,0 to +100,0 kPa | 0,0 to -101,3 kPa | 0,000 to 1,000 MPa |
WITHSTAND PRESSURE | 300 kPa | 300 kPa | 1,5 MPa |
SET PRESSURE RESOLUTION | |||
kPa | 0,1 | 0,1 | - |
MPa | - | - | 0,001 |
kgf/cm2 | 0,001 | 0,001 | 0,01 |
bar | 0,001 | 0,001 | 0,01 |
psi | 0,01 | 0,01 | 0,1 |
inHg | 0,1 | 0,1 | - |
mmHg | 1 | 1 | - |
ACCURANCY | ±2% F.S. ±1 digit of detected pressure @ 25°C ± 3°C | ||
RATED VOLTAGE | 12 to 24 V DC (±10% ripple voltage) | ||
OUTPUT TYPE | |||
PNP | Open collector 2 outputs, max current load: 125 mA | ||
ANALOG (VOLTAGE OUTPUT) | 1 to 5V ± 2,5% F.S. | ||
ANALOG (CURRENT OUTPUT) | 4 to 20mA ± 2,5% F.S. | ||
CURRENT CONSUPTION MAX. | 40 mA |
OUTPUT SHORT CIRCUIT PROTECTION | yes |
RESPONSE TIME | 2.5 ms max (anti-chattering selection: 25ms, 100ms, 250ms, 500ms, 1000ms, 1500ms) |
REPEATIBILITY | ± 0,2% F.S. ± 1 digit |
HYSTERESIS | |
ONE POINT SET MODE | |
HYSTERESIS MODE | Adjustable |
WINDOW COMPARATOR MODE | |
FUNCTION INDICATOR | OUT1 = Green ; OUT2 = Red |
ENVIROMENTAL CONDITIONS | |
TEMPERATURE OPERATION RANGE | min. 0°C ; max. 50°C (No condensation or freezing) |
TEMPERATURE STORAGE RANGE | min. -10°C ; max. 60°C (No condensation) |
AMBIENT HUMIDITY RANGE | Operation/Storage: 35 to 85 % RH |
VIBRATION | Total amplidude 1,5mm, 10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X,Y and Z |
SHOCK | 100m/s2(10G), 3 times each direction of X,Y and Z |
PROTECTION CLASS (EN 60529) | IP40 when correctly assembled |
CABLE TYPE | oil - resistance (0,15mm2) |
WEIGHT | approx. 105g (with 2m lead wire), Approx. 71g (with male connector) |
ORDER NO. GPA5S | ORDER NO. GPA5L | ORDER NO. GPA5P |
Vertical mounting brackets | Base mounting brackets | Pannel adapter |
![]() |
![]() |
![]() |
DIMENSION / CONNECTION
![]() |
||
PANEL INSTRUCTION
![]() |
||
UNIT | Pressure Unit display section | |
MAIN Display | 2 Color main display | |
SUB Display | Setting mode sub display section | |
OUT1 | Output 1 indicator | |
OUT2 | Output 2 indicator | |
Button UP | Use this button to change setting mode and pre-set final desired value | |
Button SET | Change setting mode and pre-set final desired value | |
Button DOWN | Use this button to change setting mode and pre-set final desired value |
TYPE | GPM6B0_ _ _ _ _ | GPM6E0_ _ _ _ _ | GPM7B0_ _ _ _ _ | GPM7E0_ _ _ _ _ |
PRESSURE RANGE | 0,0 to -101 kPa | 0,000 to + 1,0 MPa | 0,0 to -101 kPa | 0,000 to 1,000 MPa |
WITHSTAND PRESSURE | 300 kPa | 1,5 MPa | 300 kPa | 1,5 MPa |
SET PRESSURE RESOLUTION | ||||
kPa | 1 | - | 1 | - |
MPa | - | 0,001 | - | 0,001 |
kgf/cm2 | - | 0,01 | 0,01 | 0,01 |
bar | 0,01 | 0,01 | 0,01 | 0,01 |
psi | 0,1 | 0,1 | 0,1 | 0,1 |
inHg | - | - | - | - |
mmHg | - | - | - | - |
INDICATOR ACCURANCY | ±2% F.S. ±1 digit of detected pressure @ 25°C ± 3°C | |||
RATED VOLTAGE | By battery (CR2032 lithium, 1 year, 5 times/day) replaceable |
12 to 24 V DC (±10% ripple voltage) | ||
BACK LIGHT | yes | |||
TURN-ON INTERVAL | Display turn of after 60 sec. | |||
PRESSURE UNIT | psi, bar, mmHG, kPa user sel. |
psi, bar, Kgf/cm2, kPa user sel. |
psi, bar, Kgf/cm2, kPa user sel. |
psi, bar, Kgf/cm2, kPa user sel. |
SAMPLING RATE | 2 HZ (2 times/sec) | |||
CURRENT CONSUPTION MAX. | 10 mA | |||
![]() |
||||
REPEATIBILITY | ± 1 F.S. ± 1 digit | ± 0,2 F.S. ± 1 digit | ± 1 F.S. ± 1 digit | ± 0,2 F.S. ± 1 digit |
HYSTERESIS | ||||
ONE POINT SET MODE | ||||
HYSTERESIS MODE | ||||
WINDOW COMPARATOR MODE | ||||
LCD DISPLAY | 3 1/2 digit LCD display, 7 segment | |||
ENVIROMENTAL CONDITION | ||||
TEMPERATURE OPERATION RANGE | min. 0°C; max. 50°C (No condensation or freezing) | |||
TEMPERATURE STORAGE RANGE | min. -10°; max. 60°C (No condensation) | |||
AMBIENT HUMIDITY RANGE | Operation/Storage: 35 to 85% RH | |||
VIBRATION | total amplitude 1,5 mm, 10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X, Y and Z | |||
SHOCK | 100m/s2 (10G), 3 times each direction of X,Y and Z | |||
PROTECTION CLASS (EN 60529) | IP65 when correctly assembled | |||
CABLE TYPE | oil - resistance (0,15 mm2) | |||
WEIGHT | Approx. 40g | Approx. 60g (with 2m lead wire) Approx. 40g (with male connector) |
ORDER NO. GPA5S | ORDER NO. GPA5L | ORDER NO. GPA5P |
Vertical mounting brackets | Base mounting brackets | Pannel adapter |
![]() |
![]() |
![]() |
DIMENSION GPM6
![]()
DIMENSION GPM7
![]() |
||
PANEL INSTRUCTION
![]() |
||
BATTERY | Battery level (on GPM6) | |
UNIT | Pressure Unit display section | |
MAIN Display | Main display with pressure value | |
Button SET | Change setting pressure unit/turn on display (on GPM6) |